用于电弧检测的电力专用SoC设计

针对传统的电弧电路故障检测结果不准确的问题,设计用于电弧检测的SoC系统,并且在55nm工艺下进行流片验证。采用包含两种结构的模数转换器的片上电压源,设计了锁相环以及复位电路,精度最高可达8.67 bit。验证结果表明,本设计可提高电弧检测的准确性。     

Lactobacillus Gasseri LGZ 1029 in yogurt: rheological behaviour and volatile compound composition

Yogurt preserves and enhances nutritional value of milk. In this study, we have compared several strains to determine the physicochemical, sensory, rheological and aroma characteristics of different yogurts. We used Lactobacillus gasseri LGZ 1029 (LG), commercial probiotic L. rhamnosus (LGG) and traditional fermentation strains Streptococcus thermophilus and L. bulgaricus (SL). Results showed that the flavour and texture characteristics of mixed-strain yogurts were obviously better than in single-strain yogurts. Addition of LG increased pseudoplastic behaviour, as shown by Herschel–Bulkley model analysis of rheological behaviour. The LG + SL group also had both the highest viscosity consistency index and thickening ability. In addition, a total of 57 volatile compounds were detected in yogurts and the fermentation with the addition of LG was mainly affected by ketones. Our study suggested that a yogurt with new attributes can be produced by using LGZ 1029.     

Damage evolution in polymer due to exposure to high-pressure hydrogen gas

The use of hydrogen as a fuel is increasing exponentially, and the most economical way to store and transport hydrogen for fuel use is as a high-pressure gas. Polymers are widely used for hydrogen distribution and storage systems because they are chemically inert towards hydrogen. However, when exposed to high-pressure hydrogen, some hydrogen diffuses through polymers and occupies the preexisting cavities inside the material. Upon depressurization, the hydrogen trapped inside polymer cavities can cause blistering or cracking by expanding these cavities. A continuum mechanics–based deformation model was deployed to predict the stress distribution and damage propagation while the polymer undergoes depressurization after high-pressure hydrogen exposure. The effects of cavity size, cavity location, and pressure inside the cavity on damage initiation and evolution inside the polymer were studied. The stress and damage evolution in the presence of multiple cavities was also studied, because interaction among cavities alters the damage and stress field. It was found that all these factors significantly change the stress state in the polymer, resulting in different paths for damage propagation. The effect of adding carbon black filler particles and plasticizer on the damage was also studied. It was found that damage tolerance of the polymer increases drastically with the addition of carbon black fillers, but decreases with the addition of the plasticizer.     

强变形工艺对2519A铝合金组织与性能的影响

通过硬度测试、拉伸性能测试、透射电镜观察等分析手段研究了不同强变形工艺下2519A铝合金的力学性能与微观组织。结果表明,经50%的冷轧变形和165 ℃人工时效后,2519A合金的力学性能明显提高,其抗拉强度、屈服强度和伸长率分别为522 MPa、468 MPa和8.5%。而在冷变形前添加165 ℃×2 h预时效处理,合金的力学性能进一步提高,其抗拉强度、屈服强度和伸长率分别达到535 MPa、497 MPa和8%。预时效处理可以提高合金中θ′相的密度,使析出相分布更加均匀,有助于提高合金的力学性能。     

退火温度对冷轧DP980钢力学性能的影响

利用连续退火模拟机对DP980试验钢进行了连续退火试验,并通过扫描电镜、电子背散射衍射、透射电镜等研究了不同退火温度下(775、800、825和850 ℃),试验钢显微组织的演变规律和力学性能的变化趋势。结果表明:试验钢的屈服强度随着退火温度的升高而不断增大(从705 MPa增大到850 MPa),抗拉强度和断后伸长率则随着退火温度的升高而不断减小(抗拉强度从1150 MPa减小到1030 MPa;伸长率从8.9%减小到5.3%),这与试验钢的显微组织构成和形态分布密切相关。此外,不同退火温度下,试验钢的加工硬化率曲线均呈现单调下降的趋势。     

PDC钻头水力结构优化设计研究

在PDC钻头工作过程中，钻井液对钻头体表面的冲洗、冷却和润滑是保证钻头正常工作的一个非常重要的条件。对PDC钻头而言，水力结构（主要是中心水眼和冠部水道）设计的重要性尤其突出。以前,对钻头水力系统研究只能通过实验的方法进行,研究周期长、成本高、结构调整不方便，而数值模拟的方法在几年前还不成熟，甚至静态的复杂结构流场问题基本无法解决。为此，在提出PDC钻头水力结构优化设计原则的基础上，对PDC钻头的三维流场进行了数值模拟。模拟中考虑了钻头的喷嘴布置位置、直径、数量以及切削齿对流场的影响。计算结果表明，原设计在喷嘴布置位置和喷射角度上存在不足，以此为基础进行了水力结构的优化设计。文中的研究成果成功地应用在新型钻头水力结构的设计中，研究方法为PDC钻头水力结构优化分析奠定了理论基础。     

信息安全风险评估的模糊多准则决策方法

基于ISO/IEC17799标准建立了一个综合的信息系统风险分析框架,并运用模糊多准则决策(FMCDM)方法计算信息安全风险,根据风险等级矩阵(RLM)对信息资产风险进行级别划分,最终建立评估信息资产相关风险的完整模型。     

Investigation into polishing process of CVD diamond films

A new technique used for polishing chemical vapor deposition (CVD) diamond films has been investigated, by which rough polishing of the CVD diamond films can be achieved efficiently. A CVD diamond film is coated with a thin layer of electrically conductive material in advance, and then electro-discharge machining (EDM) is used to machine the coated surface. As a result, peaks on the surface of the diamond film are removed rapidly. During machining, graphitization of diamond enables the EDM process to continue. The single pulse discharge shows that the material of the coated layer evidently affects removal behavior of the CVD diamond films. Compared with the machining of ordinary metal materials, the process of EDM CVD diamond films possesses a quite different characteristic. The removal mechanism of the CVD diamond films is discussed.     

基于滑窗结构的软输出维特比算法的实现

文章在对软输出维特比算法(SOVA)进行推导的基础上，分析了软信息的提取过程。同时从硬件实现的角度考虑，提出了一种基于滑动窗1：3结构的SOVA算法实现方案，该算法大大降低了算法实现复杂度和译码延迟，同时通过调整滑窗参数，可以取得与非滑窗SOVA算法几乎相同的性能。     

DVB-S接收系统中包同步机制的分析与实现

本文对DVB-S接收系统中包同步搜索机制的进行了深入细致的研究，分析了相关参数对搜索性能的影响，并给出一种高效且节省资源的实现结构。